8kg hammer steel dynamic cone penetrometer
The dual mass dynamic cone penetrometer (DCP) described in this 5/8-in.-diam steel rod with a steel cone attached to one end which is driven into the pavement or subgrade by means of a sliding dual mass hammer (Fig-ure 1). The angle of the cone is 60 deg and the diameter of the base of the
Dynamic Penetrometers Engineers, 1992) is replaced by a strike plate (anvil), which is welded to the shaft. The shaft continues through the plate Dynamic penetrometers do not attempt to push the pene- and is used to guide a 2-kg slide hammer. An adjustable collar ASTM Standard Dynamic Cone Penetrometer (DCP) with 8 DYNAMIC CONE PENETROMETER (DCP) 16-T0012/A 8 kg hammer, 57.5 cm. fall. Standard:ASTM D 6951-03. Model 16-T0012/A FEATURES: Portable, hand-operated equipment. The TRL DCP is an instrument designed for the rapid insitu measurement of the structural properties of existing road pavements constructed with unbound materials.
The instrument is manufactured from stainless steel to the following specifications:- Hammer Weight measurement of 8 Kg. Tolerance is 0.004K- Drop of hammer measurement of 575mm. Tolerance is 1.0mm. - Tip included angle measurement of 60 degrees. Tolerance is 1 degree. - Tip base diameter measurement of 20mm. Tolerance is 0.25mm. Correlation of Penetration Index of Dynamic Cone 2.4.2 Dynamic Cone Penetrometer Test (DCP) The description of the Dynamic Cone Penetrometer (DCP) can be found in ASTM 6951-09 . The DCP comprises an 8kg hammer, which is lifted and dropped over a height of 575 mm. This produces a hypothetical energy of 45J, to drive a 60° cone tip vertically into the soil. The base diameter of
The Single Mass Cone Penetrometer, S-216, has a fixed 8-kg mass and is rec om mend ed for pave ment sec tions with an tic i pat ed CBR val ues between 10 and 100. The kit includes the sliding mass assembly, mm scale to mea sure penetration, 25 single-use cones, data re duc tion program dis kette and instruction manual. Dynamic Cone Penetrometer Myers Associates, Inc.The dynamic cone penetrometer (DCP) uses a 15lb steel mass falling 20 inches that strikes the anvil to cause penetration of a 1.5 diameter cone that has been seated in the bottom of a hand augered hole. The Standard Penetration Test derives N values that correlate the blows required to drive the embedded cone a depth of 1.75.
Dynamic Cone Penetrometer Test Set without Augers, Sleeved Hammer. The H-4202X DCP test set without the augers includes; (1) standard hammer assembly (H-4202.1), (1) heat-treated 45° cone penetrometer point with a 1 ft. adapter rod (H-4202.3), (4) 2.5 ft. E drill rod extensions (H-4202.225). Dynamic Cone Penetrometer. Media Sarana TeknikMachined steel, Painted, 8 kg weight. Machined steel, welded painted. Stainless steel, 16 mm dia, 100 cm scale. Water proof cloth. Be the first to review Dynamic Cone Penetrometer.. Cancel reply. Rate. Perfect Good Average Not that bad Very Poor. Save my name, email, and website in this browser for the next time I comment.
Dynamic Cone Penetrometer, or DCP, It comprises a solidified cone shaped tip, standard measurement steel rod, and a standard weight hammer(8kg), which is dropped from the highest point of the rod against an anvil to propel the tip into the ground. Parts in a DCP. Dynamic Cone Penetrometers, DCP Kits - Gilson Co.
These dutch dynamic cone penetrometer are energy-saving products and also easy to operate. These dutch dynamic cone penetrometer are CE, ISO, ROHS certified for authenticity. Browse through the massive dutch dynamic cone penetrometer ranges at and save you money on these purchases. These efficient machines are available as OEM orders and also available with customized Field Test, Field Test direct from Shanghai Civil & Road STCT-2 Soil test TRL 8kg dynamic cone penetrometer (DCP) $180.00 - $210.00 / Piece. 1.0 Pieces (Min. Order) 6 inch Sand Density Cone Apparatus for soil test. $20.00 - $60.00 / Piece. 1.0 Pieces (Min. Order) STCT-2 8kg hammer Steel Dynamic cone penetrometer. $180.00 - $230.00 / Piece. 1.0 Pieces (Min. Order) STCT-2 En standard Steel Dynamic cone
Dynamic Cone Penetrometer 8Kg Hammer (Trl Design). The TRL (Transport Research Laboratory) Dynamic Cone Penetrometer (DCP) is used for rapid in-situ measurement of the structural properties of existing road pavement constructed with unbound materials. The unit incorporates an 8 kg weight with a drop of 575 mm, and a 20 mm diameter cone fitted to the end of the shaft, allowing measurements to Penetrometer Kerucut Dinamis Standar Astm Palu 8kg - Buy Translate this page8kg hammer ASTM standard Dynamic Cone Penetrometer Deskripsi Produk 1 APLIKASI:8kg [17.6-lb] DCP dynamic cone penetrometer dengan 8kg [17.6-lb] hammer-digunakan untuk menilai di situ kekuatan undisturbed soil atau dipadatkan bahan atau keduanya.
DCP tests are performed according to the procedure established in ASTM-D6951-3 (2003). The apparatus consists of a 16mm diameter steel rod onto which a tempered steel cone is attached with a 20mm diameter base and a 60 degree tip angle. The DCP is pushed to the ground by an 8kg hammer with a 575mm free fall. The hammer correction factor is the Standard Test Method for Use of the Dynamic Cone 2.1.1 8-kg DCP dynamic cone penetrometer with an 8 kg hammer (see Fig. 1 )Ña device used to assess the in situ strength of undisturbed soil and/or compacted materials. 2.1.2 sliding attachment (see Fig. 1 )Ñan optional device steel, with the exception of the replacement point tip, which may be constructed from hardened tool steel or a similar
The Dynamic Cone Penetrometer Hammer 17.8 pounds (8kg) Drill thru Asphalt or Concrete if necessary Record reference readings (A) Rod remains stationary Lift hammer to handle The engineering properties of surface layer on very soft The typical dynamic cone penetrometer consists of an 8kg hammer that drops over a height of 575 mm, which yields a theoretical driving energy of 45J or 14.3J/cm2, and drives a cone tip with 20mm base diameter vertically into the pavement or subgrade layer. The steel rod to which the cone is attached has a smaller diameter than the
What is Dynamic Cone Penetrometer(DCP)? Print, PDF & Email Dynamic Cone Penetrometer, or DCP, is a tool used for evaluating the strength of soils on site. It also helps with monitoring theDynamic Cone Penetrometer 8Kg Hammer (Trl Design). - ELEThe TRL (Transport Research Laboratory) Dynamic Cone Penetrometer (DCP) is used for rapid in-situ measurement of the structural properties of existing road pavement constructed with unbound materials. The unit incorporates an 8 kg weight with a drop of 575 mm, and a 20 mm diameter cone fitted to the end of the shaft, allowing measurements to be made down to a depth of approximately 850 mm.